Utilization of Chitosan as an Inhibitor to Improve the Corrosion Resistance of Low-Carbon Steel
DOI:
https://doi.org/10.23887/jstundiksha.v12i1.51385Keywords:
Corrosion, Low-carbon Steel, ChitosanAbstract
The Batam industry materials are steel, an alloy material between iron and carbon, and a few other elements. Low-carbon steel is one type of metal. However, this low-carbon steel has the disadvantage of corrosion resistance, mainly if applied to corrosive environments. In the utilization of Low carbon steel in the industry, corrosion can cause problems and cost a lot of money in its maintenance. Chitosan contained in invertebrate animals is predicted to be able to prevent corrosion as an inhibitor. This study aims to analyze the optimal conditions of chitosan inhibitors against the corrosion rate of low-carbon steel in environments with variations in the length of immersion of specimens in corrosive media. This study is a true-experimental study with a pre-post-test design. The determination of the optimal conditions of corrosion inhibition of low-carbon steel plate specimens by chitosan was carried out with variations in the parameters of HCl concentration, specimen immersion time, and chitosan concentration. The analysis carried out is the measurement of specimen weight loss in each parameter by determining the difference in weight before and after the experiment and determining the efficiency of the inhibitor. The experiment’s results showed that the optimal conditions of inhibition of corrosion were at 1M HCl, 400ppm chitosan, and a soaking time of 3 days with an efficiency of 48%. The efficiency value of this optimum corrosion inhibition of chitosan in low-carbon steel is 48%. To improve the efficiency of corrosion inhibition, it is necessary to further research with higher accuracyTo determine the effect of inhibition of corrosion using chitosan on the quality of steel surfaces, it is necessary to analyze the steel surface structure using ultrasonic testing or using XRD Analysis.
References
Abdallah, M. (2004). Guar gum as corrosion inhibitor for carbon steel in sulfuric acid solutions. Portugaliae Electrochimica Acta, 22, 161–175. http://www.peacta.org/articles_upload/PEA2222004161.pdf.
Ali, F., Saputri, D., & Nugroho, R. F. (2014). Pengaruh waktu perendaman dan konsentrasi ekstrak daun jambu biji (Psidium guajava, Linn) sebagai inhibitor terhadap laju korosi baja SS 304 dalam larutan garam dan asam. Jurnal Teknik Kimia, 20(1).
Anam, K., Idris, F., & Syakti, A. D. (2019). Analisis Kandungan Logam Berat Pb dan Cd pada Siput Gonggong (Strombus sp) di Perairan Kecamatan Bukit Bestari. Buana Sains, 19(1), 37. https://doi.org/10.33366/bs.v19i1.1525.
Atkins, P., Atkins, P. W., & de Paula, J. (2014). Atkins’ physical chemistry. Oxford university press.
Bentrah, H., Rahali, Y., & Chala, A. (2014). Gum Arabic as an eco-friendly inhibitor for API 5L X42 pipeline steel in HCl medium. Corrosion Science, 82, 426–431. https://doi.org/10.1016/j.corsci.2013.12.018.
Bilaut, I., Gauru, I., Wogo, H. E., & Lapailaka, T. (2019). Synthesis And Characterization Of Chitosan-Magnesium (Ii) Complex Ions From Shrimp Shells. Chemistry Notes, 1(1), 1–10. https://ejurnal.undana.ac.id/CN/article/view/1574.
Cheng, F., Liang, J., Tao, Z., & Chen, J. (2011). Functional materials for rechargeable batteries. Advanced Materials, 23(15), 1695–1715. https://doi.org/10.1002/adma.201003587.
Dinov, K. C. (2022). Analisa Pengaruh Variasi Heat Input Dengan Metoda Pengelasan Smaw Pada Material Baja Karbon S355J2N Dengan Pengujian Hardness Test. Universitas Islam Riau.
El-Haddad, M. N. (2013). Chitosan as a green inhibitor for copper corrosion in acidic medium. International Journal of Biological Macromolecules, 55, 142–149. https://doi.org/10.1016/j.ijbiomac.2012.12.044.
Gemala, M. (2018). Degradasi Senyawa Carbaryl Dalam Pestisida Sevin 85 S Secara Sonolisis, Ozonolisis Dan Sonozolisis. SCIENTIA: Jurnal Farmasi Dan Kesehatan, 8(2), 130–136.
Guo, H. F., & An, M. Z. (2005). Growth of ceramic coatings on AZ91D magnesium alloys by micro-arc oxidation in aluminate–fluoride solutions and evaluation of corrosion resistance. Applied Surface Science, 246(1–3), 229–238. https://doi.org/10.1016/j.apsusc.2004.11.031.
Haruna, K., & Saleh, T. A. (2021). N, N′-Bis-(2-aminoethyl) piperazine functionalized graphene oxide (NAEP-GO) as an effective green corrosion inhibitor for simulated acidizing environment. Journal of Environmental Chemical Engineering, 9(1), 104967. https://doi.org/10.1016/j.jece.2020.104967.
Hasanin, M., & Al Kiey, S. A. (2021). Development of ecofriendly high performance anti-corrosive chitosan nanocomposite material for mild steel corrosion in acid medium. Biomass Conversion and Biorefinery, 1–14. https://doi.org/10.1007/s13399-021-02059-8.
Hendrayady, A. (2018). Strategi Pembangunan Wilayah Perbatasan Provinsi Kepulauan Riau. Jurnal Ilmu Administrasi Negara (JUAN), 6(1), 1–10. http://ojs.umrah.ac.id/index.php/juan/article/view/777.
Herdianti, H., Sari, N., Saputra, R., & Hariansyah, F. D. (2020). Kalsium Hipoklorit (CaClO2) sebagai Pengganti Larvasida Aedes Aegypti. Jurnal Kesehatan, 11(3), 422–428. https://ojs.umrah.ac.id/index.php/juan/article/view/777.
Hidayatullah, S., Gapsari, F., & Setyarini, P. H. (2019). Perilaku Korosi Besi ASTM A36 pada Asam Klorida (HCl) dengan Inhibitor Kitosan Sisik Ikan. Prosiding SENIATI, 336–342. https://ejournal.itn.ac.id/index.php/seniati/article/view/460.
Jalaluddin, J., Ishak, I., & Rosmayuni, R. (2017). Efektifitas inhibitor ekstrak tanin kulit kayu akasia (Acacia Mangium) terhadap laju korosi baja lunak (ST. 37) dalam media asam klorida. Jurnal Teknologi Kimia Unimal, 4(1), 89–99. https://ojs.unimal.ac.id/jtk/article/view/66.
Khaled, K. F. (2003). The inhibition of benzimidazole derivatives on corrosion of iron in 1 M HCl solutions. Electrochimica Acta, 48(17), 2493–2503. https://doi.org/10.1016/S0013-4686(03)00291-3.
M. Ways, T. M., Lau, W. M., & Khutoryanskiy, V. V. (2018). Chitosan and its derivatives for application in mucoadhesive drug delivery systems. Polymers, 10(3), 267. https://doi.org/10.3390/polym10030267.
Megahed, M. M., Abdel Bar, M. M., & El-Shamy, A. M. (2021). Polyamide coating as a potential protective layer against corrosion of iron artifacts. Egyptian Journal of Chemistry, 64(10), 3–4. https://journals.ekb.eg/article_174924.html.
Messali, M., Lgaz, H., Dassanayake, R., Salghi, R., Jodeh, S., Abidi, N., & Hamed, O. (2017). Guar gum as efficient non-toxic inhibitor of carbon steel corrosion in phosphoric acid medium: Electrochemical, surface, DFT and MD simulations studies. Journal of Molecular Structure, 1145, 43–54. https://doi.org/10.1016/j.molstruc.2017.05.081.
Mobin, M., Zehra, S., & Parveen, M. (2016). L-Cysteine as corrosion inhibitor for mild steel in 1 M HCl and synergistic effect of anionic, cationic and non-ionic surfactants. Journal of Molecular Liquids, 216, 598–607.
Odewunmi, N. A., Jafar Mazumder, M. A., Ali, S. A., Aljeaban, N. A., Alharbi, B. G., Al-Saadi, A. A., & Obot, I. B. (2020). Impact of degree of hydrophilicity of pyridinium bromide derivatives on HCl pickling of X-60 mild steel: Experimental and theoretical evaluations. Coatings, 10(2), 185. https://doi.org/10.1016/j.molliq.2016.01.087.
Oguzie, E. E., Li, Y., & Wang, F. H. (2007). Effect of 2-amino-3-mercaptopropanoic acid (cysteine) on the corrosion behaviour of low carbon steel in sulphuric acid. Electrochimica Acta, 53(2), 909–914. https://doi.org/10.1016/j.electacta.2007.07.076.
Palumbo, G., Górny, M., & Banaś, J. (2019). Corrosion inhibition of pipeline carbon steel (N80) in CO2-saturated chloride (0.5 M of KCl) solution using gum arabic as a possible environmentally friendly corrosion inhibitor for shale gas industry. Journal of Materials Engineering and Performance, 28(10), 6458–6470. https://doi.org/10.1007/s11665-019-04379-3.
Pambudi, G. B. R. (2018). Sintesis Kitosan Larut Air Dari Limbah Cangkang Kepiting. Institut Teknologi Sepuluh Nopember.
Refait, P., Grolleau, A.-M., Jeannin, M., Rémazeilles, C., & Sabot, R. (2020). Corrosion of carbon steel in marine environments: role of the corrosion product layer. Corrosion and Materials Degradation, 1(1), 10. https://doi.org/10.3390/cmd1010010.
Roy, P., Karfa, P., Adhikari, U., & Sukul, D. (2014). Corrosion inhibition of mild steel in acidic medium by polyacrylamide grafted Guar gum with various grafting percentage: Effect of intramolecular synergism. Corrosion Science, 88, 246–253. https://doi.org/10.1016/j.corsci.2014.07.039.
Sakinah, F. (2020). Peningkatan Kualitas Biopolimer (Pla) Nanokomposit Modifikasi Filler Bentonit Dan Kitosan Anti-Bakteri. Jurnal Sains Dan Teknologi Reaksi, 18(01). http://e-jurnal.pnl.ac.id/JSTR/article/view/2235.
Saputra, R. (2019). Pemanfaatan Kulit Pisang Dalam Degradasi Zat Aktif Piridaben Pada Pestisida Samite 135EC. Jurnal Ipteks Terapan, 13(1), 1–11. http://ejournal.lldikti10.id/index.php/jit/article/view/3439-14818.
Saputra, R., & Oktarizal, H. (2017). Pemanfataan Serbuk Sekam Padi Sebagai Adsorben Untuk Menurunkan Konsentrasi Senyawa Piridaben Pada Pestisida Samite 135EC. Chempublish Journal, 2(2), 42–53. https://doi.org/10.22437/chp.v2i2.4475.
Sari, N. H., Suteja, S. T., & Syarif Hidayatullah, S. T. (2021). Pengantar Inhibitor Korosi Alami. Deepublish.
Shamsa, A., Barker, R., Hua, Y., Barmatov, E., Hughes, T. L., & Neville, A. (2020). Performance evaluation of an imidazoline corrosion inhibitor in a CO2-saturated environment with emphasis on localised corrosion. Corrosion Science, 176, 108916. https://doi.org/10.1016/j.corsci.2020.108916.
Sinaga, A. J., & Manurung, C. (2020). Analisa Laju Korosi dan Kekerasan Pada Stainless Steel 316 L Dalam Larutan 10% NaCl Dengan Variasi Waktu Perendaman. Sprocket Journal of Mechanical Engineering, 1(2), 92–99. https://doi.org/10.36655/sprocket.v1i2.186.
Siregar, T., Sitorus, E., Priastomo, Y., Bachtiar, E., Siagian, P., Mohamad, E., Gurning, K., Hasibuan, F. A., Destiarti, L., & Marzuki, I. (2021). Korosi dan Pencegahannya. Yayasan Kita Menulis.
Sofika, S. (2017). Aktivitas Anti Jamur Dari Edible Coating Kitosan-Minyak Temu Mangga (Curcuma mangga valeton & zijp) Terhadap Buah Stroberi (Fragaria vasca L.).
Stiadi, Y., Arief, S., Aziz, H., Efdi, M., & Emriadi, E. (2019). Inhibisi Korosi Baja Ringan Menggunakan Bahan Alami Dalam Medium Asam Klorida. Jurnal Riset Kimia, 10(1), 51–65. https://doi.org/10.25077/jrk.v12i2.321.
Tan, B., He, J., Zhang, S., Xu, C., Chen, S., Liu, H., & Li, W. (2021). Insight into anti-corrosion nature of Betel leaves water extracts as the novel and eco-friendly inhibitors. Journal of Colloid and Interface Science, 585, 287–301. https://doi.org/10.1016/j.jcis.2020.11.059.
Umoren, S A. (2008). Inhibition of aluminium and mild steel corrosion in acidic medium using Gum Arabic. Cellulose, 15(5), 751–761. https://doi.org/10.1007/s10570-008-9226-4.
Umoren, S A, Obot, I. B., Ebenso, E. E., Okafor, P. C., Ogbobe, O., & Oguzie, E. E. (2006). Gum arabic as a potential corrosion inhibitor for aluminium in alkaline medium and its adsorption characteristics. Anti-Corrosion Methods and Materials, 53 (5), 277-282. https://doi.org/10.1108/00035590610692554.
Umoren, Saviour A, AlAhmary, A. A., Gasem, Z. M., & Solomon, M. M. (2018). Evaluation of chitosan and carboxymethyl cellulose as ecofriendly corrosion inhibitors for steel. International Journal of Biological Macromolecules, 117, 1017–1028. https://doi.org/10.1016/j.ijbiomac.2018.06.014.
Venkateswarlu, K., Rameshbabu, N., Sreekanth, D., Sandhyarani, M., Bose, A. C., Muthupandi, V., & Subramanian, S. (2013). Role of electrolyte chemistry on electronic and in vitro electrochemical properties of micro-arc oxidized titania films on Cp Ti. Electrochimica Acta, 105, 468–480. https://doi.org/10.1016/j.electacta.2013.05.032.
Wildan Ilyas, M. (2019). Perancangan Sistem Impressed Current Cathodic Protection (Iccp) Anoda Korban Pada Pipa Baja Dengan Prototype Berbasis Arduino Uno (Studi Kasus: Pt. Pln (Persero) Pembangkitan Tanjung Jati B Unit 3&4). Vokasi undip.
Downloads
Published
How to Cite
Issue
Section
License
Copyright (c) 2022 Mega Gemala, Aulia Fajrin, Adhe Aryswan, Roni Saputra, Ihsan Saputra, Sriyanto
This work is licensed under a Creative Commons Attribution-ShareAlike 4.0 International License.
Authors who publish with the Jurnal Sains dan Teknologi (JST) agree to the following terms:
- Authors retain copyright and grant the journal the right of first publication with the work simultaneously licensed under a Creative Commons Attribution License (CC BY-SA 4.0) that allows others to share the work with an acknowledgment of the work's authorship and initial publication in this journal.
- Authors are able to enter into separate, additional contractual arrangements for the non-exclusive distribution of the journal's published version of the work (e.g., post it to an institutional repository or publish it in a book), with an acknowledgment of its initial publication in this journal.
- Authors are permitted and encouraged to post their work online (e.g., in institutional repositories or on their website) prior to and during the submission process, as it can lead to productive exchanges, as well as earlier and greater citation of published work. (See The Effect of Open Access)
